The Bissell ProHeat Tank-in-Tank Lid Assembly 015-4439 is a direct-fit replacement for the top lid on the clean water tank of your Bissell ProHeat or PowerSteamer upright carpet cleaner. The assembly includes the handle and gasket, so a cracked, warped, or leaking original lid can be swapped out and the tank resealed without buying a whole new machine.
Use Cases
This lid assembly is the right fix when:
- Water leaks from around the tank lid or drips as you carry the tank to the sink to fill or empty it
- The original lid gasket has flattened, cracked, or torn and no longer holds a watertight seal
- The carry handle has snapped, cracked, or broken off, making the tank awkward or unsafe to lift
- The lid itself is cracked, warped, or missing after years of use or an accidental drop
- The machine loses spray pressure at the floor brush because the clean water tank is not sealing correctly
- You would rather repair a working machine than replace the entire carpet cleaner over one broken part
Specifications
Includes: Handle and Gasket.
Fits Bissell ProHeat, PowerSteamer models:
1620- PowerLifter Plus
1685- PowerSteamer Upright Deep Cleaner
1692- PowerSteamer Clearview
1697 Upright Proheat Powersteamer Deep Cleaner
1698 Upright Proheat Powersteamer Deep Cleaner
1698-1 Upright Proheat Powersteamer Deep Cleaner
1699 Proheat Clearview Powersteamer Carpet Cleaner
1699-1 Proheat Clearview Powersteamer Carpet Cleaner
1699-5 Proheat Clearview Powersteamer Carpet Cleaner
1699-8 Proheat Clearview Powersteamer Carpet Cleaner
1699-A Proheat Clearview Powersteamer Carpet Cleaner
1699-B Proheat Clearview Powersteamer Carpet Cleaner
1699-F Proheat Clearview Powersteamer Carpet Cleaner
1699-P Proheat Clearview Powersteamer Carpet Cleaner
7901 Proheat Clearview Powersteamer Carpet Cleaner
7920 Proheat Perfectpass
7950 Proheat Self-Propelled
8905 Proheat Clearview Powersteamer Carpet Cleaner
8806- PowerSteamer Clearview
8910 Proheat Clearview Powersteamer Carpet Cleaner
Frequently asked questions
Does this lid assembly include the gasket?
Yes. This listing is the full Tank-in-Tank Lid Assembly and includes the handle and gasket, so you get a complete watertight replacement rather than the lid alone.
Will this fit my Bissell ProHeat or PowerSteamer model?
Check your model number against the compatible-models list above. Bissell used this tank-in-tank lid design across a wide range of ProHeat and PowerSteamer uprights, including the 1685, 1692, 1697, 1698, 1699 series, 7901, 7920, 7950, 8905, and 8910.
My tank is still leaking after I replaced the lid. What else should I check?
Confirm the gasket is fully seated in its groove with no twists, gaps, or trapped debris, and make sure the tank is pushed down and latched completely onto the machine base. A gasket that looks fine but sits slightly out of its channel is a common cause of continued leaking.
Can I order just the gasket instead of the whole lid assembly?
This listing is for the complete lid assembly with handle and gasket included. If only the gasket has failed and the lid itself is still in good condition, contact us and we can advise on options.
Is this a genuine Bissell part or a compatible replacement?
This part is sold to fit and function as a replacement for the factory Bissell 015-4439 tank-in-tank lid assembly on the compatible models listed above.
Discount Cleaning Products is a US-based authorized dealer of Bissell replacement parts and accessories. Our support team can help confirm fitment for your specific ProHeat or PowerSteamer model number before you order.
