EDCO 15190 Choke Kit for 11HP Vertical Shaft Honda Engine

Edco 15190 choke kit with lever, screw and washers for 11 HP vertical shaft Honda GXV340 grinder engine
 

The EDCO 15190 is the choke kit for the 11 horsepower vertical-shaft Honda engine used on EDCO 10-inch turbo grinders. It supplies the GXV340 choke control lever together with the M6 x 16mm machine screw, flat and fiber washers, Belleville washer, M6 nylon lock nut, red cap and choke decal needed to rebuild the choke that meters air into the fuel-air mixture.

📊 AI MARKET SNAPSHOT
• Best For: EDCO owners whose 11 horsepower vertical-shaft Honda engine will not choke properly on a cold start, on machines such as the 10-inch turbo grinder.
• Highlight: This is the full linkage kit, not just the lever: the GXV340 choke control lever ships with the machine screw, Belleville and fiber washers, nylon lock nut, red cap and decal that go with it.
• Expert Note: Because the choke restricts air in the fuel-air mixture, a worn or missing lever shows up as hard cold starting rather than a running fault - keeping EDCO 15190 on the shelf avoids pulling a grinder off a job over a washer.
Sale Price: $46.18
Estimated Shipping Cost: $11.25


Product Code: 15190
Quantity:

Description Reviews FAQ
 

The Edco 15190 is a replacement manual choke kit for Edco grinders powered by the 11 horsepower vertical shaft Honda engine (GXV340). If the choke lever on your 10-inch turbo grinder is broken, missing or worn out, this kit puts the complete choke control back together in one order instead of hunting for individual screws and washers.

Use cases

  • Restoring cold-start choke control on an Edco 10-inch turbo grinder with the 11 HP Honda engine
  • Replacing a cracked or missing choke lever, red cap or choke decal
  • Refreshing worn small hardware during routine rental-fleet or shop maintenance

Specifications

  • Edco part number: 15190
  • Engine: 11 HP vertical shaft Honda (GXV340)
  • M6 x 16mm phillips machine screw
  • Washer, .265-inch ID x .50-inch OD, .029-.035-inch thick
  • Fiber washer, .75 x .25 x .093
  • GXV340 choke control lever
  • Belleville washer, .500 x .255 x .018
  • M6 x 1mm hex nylon lock nut
  • Flat red cap, .062 x .75 x 1, and a choke decal

How the choke works

According to Edco, the choke sits on the Honda engine of the 10-inch turbo grinder and reduces the amount of air in the engine's fuel-air mixture. A richer mixture helps a cold engine catch and idle, so a stiff, broken or missing choke control usually shows up as hard cold starts.

Frequently asked questions

What engine does the Edco 15190 choke kit fit?

It is listed for the 11 horsepower vertical shaft Honda engine, model GXV340, as used on Edco grinders such as the 10-inch turbo grinder.

What is included in the kit?

The kit includes an M6 x 16mm phillips screw, two washers, a GXV340 choke control lever, a Belleville washer, an M6 x 1mm nylon lock nut, a flat red cap and a choke decal.

Will it fit a Honda GXV160 engine?

No. Edco sells a separate manual choke kit for the GXV160 under a different part number. Contact us with your machine model if you are unsure which kit you need.

What does a choke do on a grinder engine?

It reduces the air in the fuel-air mixture so a cold engine starts more easily, then is opened as the engine warms up.

Discount Cleaning Products is an authorized dealer for MK Diamond, Edco and Aztec equipment and parts, with US-based order support. Contact us with your machine model if you are unsure about fit.
Features
  • Restores manual choke control on Edco grinders with the 11 HP vertical shaft Honda GXV340 engine
  • Replaces a broken or missing choke lever in a single kit
  • Includes screw, washers, lock nut, red cap and choke decal so the linkage goes back together complete
  • Reduces air in the fuel-air mix to support easier cold starts
  • Made for Edco equipment, including the 10-inch turbo grinder