This is a genuine Sandia 1-1/2 inch black vacuum hose in a 25-foot length, supplied cuffed at both ends with the 10-0196 and 10-0155 cuffs for auto fill and dump service. The long run is the point: it is the hose you use when the machine stays where it is and the operator has to move - filling an extractor from a remote water source, dumping a recovery tank to a floor drain across the room, or reaching a work area without repositioning equipment mid-job.
Vacuum hose is a wear item on any backpack or extractor, and it fails in ways that are easy to miss. A hose that has been stepped on, run over by a cart, or dragged around door frames for a season develops flat spots and pinhole splits. The machine still runs and the operator still hears suction at the motor, but airflow at the tool has dropped, and the crew ends up making two passes where one used to do. Sandia is direct about this: do not use the vacuum if any hose is damaged, cut, or punctured.
Built for
- Carpet cleaning crews filling and dumping extractors without dragging the machine to the sink.
- Auto fill and dump setups that need a dedicated long run rather than the machine hose.
- Truck-mount and portable operators working buildings where the drain is nowhere near the work.
- Fleet shops replacing a long hose that has split at the cuffs.
Specifications
Sandia part number 10-0024-25. Black vacuum hose, 1-1/2 inch diameter, 25-foot length, fitted with two cuffs (Sandia 10-0196 and 10-0155) for auto fill and dump. Genuine Sandia part, manufactured in the USA.
Warranty
Sandia is committed to deliver the best quality, and Sandia products are covered by a comprehensive warranty:
- 2-year warranty on all vacuum motors
- 2-year warranty on 100 psi pumps only; 1-year warranty on all other pumps
- 90 days on parts, tools, and accessories
Warranty terms shown are the terms of record for this listing. Coverage applies to defects in material and workmanship under normal use and service, and does not cover wear items, misuse, or repairs made by an unauthorized service provider.
Frequently asked questions
How do I know when a vacuum hose needs replacing?
Run the machine and pinch the hose closed at the tool end. If suction does not build sharply, air is getting in somewhere along the length. Then flex the hose section by section and look for flat spots, splits at the cuffs, and pinholes. Any cut or puncture means the hose should be taken out of service.
Does hose length affect suction?
Yes. Every additional foot of hose adds resistance, so a long hose trades some airflow at the tool for reach. Use the shortest length that covers the work: a short hose for a backpack worn on the operator, a long one only where the machine has to stay put while the operator moves.
Why buy genuine Sandia hose instead of generic hose?
Cuff fit. Generic hose in a nominal 1-1/2 inch size often will not seat tightly on Sandia cuffs and tools, and a loose joint leaks air at exactly the point where you need airflow. Genuine hose is cut and sized to the same specification as the original.
What are the two cuffs on this hose?
It ships with the Sandia 10-0196 and 10-0155 cuffs already fitted, which is the pairing Sandia specifies for auto fill and dump use. Because both ends are finished, it goes straight into service without you sourcing and fitting hardware.
Is 25 feet too long for a backpack vacuum?
For a backpack worn on the operator, yes - the machine travels with you, so a 4-foot hose is the right tool. This 25-foot length is meant for stationary equipment and fill or dump runs where the reach is what you are buying.
Discount Cleaning Products is an authorized dealer for the brands we carry, and we stock genuine manufacturer parts rather than generic substitutes. Our US-based team can help you confirm the right part number for your machine model and serial number before you order, so the part you receive is the part that fits. If you are not certain which version your equipment uses, contact us with your model number and we will check it against the manufacturer parts list for you.
