The BE Pressure WP-2065HL is a 2-inch self-priming water transfer pump powered by a Honda GX200 engine, delivering up to 158 gallons per minute of moving capacity. Built for contractors, landscapers, farm operators, pond maintenance crews, and emergency-response teams, this pump moves clean water - it is the right tool for filling tanks, dewatering excavations, transferring irrigation water, draining swimming pools, and emergency dewatering of basements and crawl spaces.
Who buys this pump
The 2-inch class is the most-shipped size in the BE water transfer line - big enough to move serious volume, small enough that one or two people can move it on a job. Construction crews use it for dewatering footings and excavations after rain. Pool service techs use it for draining and refilling pools faster than any built-in pump cycle. Farm operators move irrigation water between holding tanks and field lines. Pond and water-feature maintenance pros drain and refill ornamental ponds. Plumbers and emergency-response crews keep one on the truck for basement and crawl-space flooding.
Top use cases
- Construction dewatering - footings, excavations, and trenches after heavy rain.
- Pool and spa drain and fill - much faster turnover than the pool's built-in pump for full water-change service.
- Agricultural water transfer - holding tank to irrigation line, or stock-tank refill from a creek or pond source.
- Pond and water-feature service - drain for cleaning and refill from a clean source.
- Emergency basement and crawl space dewatering - first-response after weather events when shop vacs cannot keep up.
Specifications
- Engine: Honda GX200 commercial OHV gas engine
- Pump body: 2-inch inlet and outlet ports
- Maximum flow: up to 158 GPM
- Self-priming design - no need to flood-prime when starting
- Application: clean and lightly-debris-laden water (not for trash water with solids)
- Frame: tubular steel roll cage with carry handles
- Recoil start with low-oil shutdown
Frequently asked questions
Clean-water vs. trash pump - which do I need?
The WP-2065HL is a clean-water transfer pump - it handles water with light debris (sand, fine sediment) but not trash water with leaves, sticks, or larger solids. For dewatering construction excavations with significant solids, a dedicated 2-inch trash pump is the right choice; for tank filling, pool service, irrigation transfer, and post-rain dewatering of clean water, this is the right tool.
How do I prime it?
Self-priming - fill the pump body with water through the priming port at first start, then start the engine. The pump will pull suction from the inlet hose. After the first prime, normal cycles do not require re-priming as long as the pump body holds water between uses. Drain before any below-freezing storage to prevent frost cracks.
What suction lift can it handle?
2-inch transfer pumps in this class typically handle 25-26 feet of suction lift at sea level. Real-world performance drops with elevation, hose length, and inlet hose condition. Keep the inlet hose as short as practical and use a foot valve and strainer to keep prime and prevent debris.
Suction and discharge hose sizing?
Match the hose to the pump - 2-inch suction hose with cam-lock fittings on the inlet and 2-inch discharge hose on the outlet. Larger hose on the discharge will not increase flow above pump rating. Reinforced suction hose is critical - cheap garden hose collapses under suction.
Storage and freeze protection?
Drain the pump body completely before any below-freezing storage. Run the pump dry briefly after closing inlet and outlet valves to clear residual water. Frost cracks on the volute or seals are the most preventable failure on water transfer pumps.
Engine break-in and routine maintenance?
Honda GX200 engines do best with a brief break-in: run light load for the first hour, then change oil at 5 hours and again at 20 hours. After that, oil change every 100 hours of run time or annually, whichever comes first. Inspect the air filter monthly under dusty job-site conditions, change the spark plug at 100 hours, and add fuel stabilizer if the unit will sit between projects. Most no-start calls trace back to stale fuel or a clogged air filter on pumps that were stored without prep.
Foot valve and strainer setup at the inlet?
A foot valve at the bottom of the inlet hose keeps the pump primed between cycles and prevents drawback when the engine stops. Pair it with a coarse strainer sized for the application - a finer strainer for clean tank-to-tank transfer, an open basket for site dewatering with light debris. Suspend the strainer slightly above the bottom of the source so it does not draw sediment, and check it before each long run to keep flow steady.
Discount Cleaning Products is an authorized BE Power Equipment dealer. We stock and ship the WP-2065HL direct from BE distribution with full factory warranty and access to Honda OEM engine parts and BE pump replacement parts.
