An upright vacuum that runs but stops picking up carpet usually has one of three problems: a stretched belt, a blocked airway, or a brushroll that has stopped doing its job. This is the 12 inch replacement brushroll assembly for Eureka 4700, 4703 and 4750 series uprights - the wood-core beater bar with bearing ends that agitates carpet pile so the vacuum has something to lift.
Why brushrolls fail
Two things wear out. The bristles flatten and round over with use, at which point the roller spins but no longer digs into the pile - the vacuum skates across carpet and only picks up what is loose on top. Separately, the bearings at the ends pack with hair and thread until the roller drags or seizes. A dragging roller is the reason belts keep burning through: the belt is being asked to turn something that will not turn freely, so it stretches, glazes and snaps. Repair shops see the same pattern constantly - the customer keeps buying belts when the actual fault is the roller.
Use cases
- Vacuum runs but leaves carpet fibers standing - worn bristles no longer agitate the pile.
- Repeat belt failures - a stiff or seized brushroll destroys belts one after another; replacing the roller stops the cycle.
- Roller will not spin by hand - hair-packed or failed end bearings.
- Restoring an older Eureka upright - a brushroll is a low-cost way to bring a machine that still runs well back to full performance.
- Fleet maintenance - offices, rentals and cleaning services running several identical Eureka uprights.
Fit
This assembly is listed for the Eureka 4700 and 4750 upright families, including 4700, 4701, 4702, 4703 and 4750 variants, and is cross-referenced by parts sellers to numbers including 60844A-10 and 60844-5. Eureka used a number of letter suffixes across these series and retailer fit lists do not always agree on every sub-model. Before ordering, pull your existing brushroll and check the length and the pulley groove against the specifications below, or match the number stamped on the old roller.
Installation notes
Replacing a brushroll on these machines is a hand-tool job: remove the bottom plate, lift the old roller out of its end mounts, slip the belt onto the new roller pulley and seat it back in. It is worth fitting a fresh belt at the same time - an old belt that has been running against a seized roller is already stretched, and it is the cheaper of the two parts.
Specifications
- 12 inch brushroll assembly
- Wood roller core
- Nylon bristles
- Ball bearing end caps
- Listed for Eureka 4700, 4701, 4702, 4703 and 4750 series uprights
- Cross-referenced to 60844A-10 and 60844-5 by parts retailers
- Brushroll only - belt not included
Frequently asked questions
Will it fit my exact Eureka model?
It is listed for the 4700 and 4750 upright families including 4700, 4701, 4702, 4703 and 4750 variants. Eureka used many letter suffixes across these series and retailer fit lists differ on some sub-models, so compare the length and pulley groove of your existing roller before ordering.
Does a belt come with it?
No. The brushroll is sold on its own. Fitting a new belt at the same time is recommended, because a belt that has been driving a seized roller is usually already stretched.
Will this stop my belt from burning?
If the belt failures were caused by a dragging or seized brushroll, yes. If the roller in your machine still spins freely by hand, the belt problem is more likely the belt itself or a jammed airway.
How do I know the brushroll is worn out rather than the belt?
Spin the roller by hand with the machine unplugged. If it binds, grinds or will not turn, the roller is the fault. If it spins freely but the carpet is not being agitated, look at the bristles - flattened, rounded bristles no longer reach into the pile.
Is this an OEM Eureka part?
This is a replacement brushroll assembly built to the Eureka specification for these models. Match it against the part number on your existing roller if OEM sourcing is a requirement.
Discount Cleaning Products stocks brushrolls, belts, filters and bags for vacuum lines that stay in service long after the machines leave the store shelf, backed by US-based customer support.
