Warehouses, shops and production floors get hot from the roof down, and a floor fan only moves the air it can reach. The Airmaster 71726 is a 30-inch non-oscillating air circulator that bolts to a wall or hangs from a ceiling, so it pushes a directed column of air across a work area without taking up a single square foot of floor space. Plant managers and facility maintenance teams specify it when they need real air movement over an assembly line, a loading dock or a wash bay and cannot afford a tripping hazard or an extension cord run.
Built for these use cases
- Directing airflow over assembly lines, packing stations and shop benches where floor space is at a premium
- Loading docks and bay doors that need constant air movement without a fan on the ground
- Drying floors faster after scrubbing or mopping in warehouses and large corridors
- Destratifying hot air that collects near the ceiling in high-bay buildings
- Wash bays, kennels and equipment rooms where a fixed, out-of-the-way mount is safer than a pedestal
Fit and compatibility
The 71726 is the wall and ceiling mount version of Airmaster's 30-inch industrial circulator, catalogued as the I-30W2A. It is a fixed, non-oscillating head on a mounting bracket, which is a different product from Airmaster's pedestal, drum and yoke-mount fans even though they share blade sizes. If you are replacing an existing Airmaster unit, check the model tag on the motor housing rather than going by blade diameter alone, because Airmaster builds several 30-inch fans with different motors, speed sets and mounts. For a new installation, the questions that matter are whether you have structure that can carry the fan, a 115 V single-phase circuit within reach of the 15 foot cord, and enough clearance for the head to tilt through its range.
Specifications
- Blade size: 30 inches, galvanized steel
- Mounting: Wall or ceiling, non-oscillating
- Airflow: 7,185 CFM on high, 5,300 CFM on medium, 3,415 CFM on low
- Motor: 1/3 HP, permanent split capacitor, totally enclosed air-over, ball bearing
- Electrical: 115 V, 1-phase, 3 A, 270 W, 60 Hz
- Speeds: 3-speed control
- Air velocity: 690 FPM at 20 feet
- Sound level: 76 dBA
- Maximum ambient temperature: 104 degrees F
- Cord: 15 ft
- Dimensions: 15.25 in. x 33.4 in. x 27 in.
- Listings: UL and cUL listed, OSHA compliant guard spacing
- Model reference: I-30W2A
Installation and care
- Mount to structural framing or a rated ceiling support, not to drywall or sheet panel alone.
- Verify the circuit is 115 V single-phase and can carry the 3 amp draw along with anything else on it.
- Aim the head before final tightening, then check the tilt holds under vibration after the first hour of running.
- Blow dust off the guard and blade on a scheduled interval, since a dust-loaded blade loses airflow and puts the assembly out of balance.
- Keep the guard in place at all times, as the spacing is what makes the installation OSHA compliant.
In high-bay buildings the biggest gain from a ceiling-mounted circulator is usually destratification. Hot air collects at the roof line and stays there, and pushing it back down evens out the temperature across the floor without touching the heating system.
Frequently asked questions
Does the Airmaster 71726 oscillate?
No. It is a fixed non-oscillating circulator. The head tilts so you can aim the air column where it is needed, but it does not sweep side to side. Non-oscillating models put more sustained airflow on one target area.
Can it mount to a ceiling as well as a wall?
Yes. The 71726 is supplied as a combination wall and ceiling mount unit, so the same fan can be bracketed to a wall or suspended from overhead structure.
What power supply does it need?
Standard 115 V single-phase, 60 Hz service drawing about 3 amps and 270 watts. It ships with a 15 foot cord.
How far will it throw air?
Air velocity is rated at 690 FPM measured 20 feet from the fan on high speed, which is why it works well over long benches and dock areas.
Is it suitable for hot environments?
It is rated for ambient temperatures up to 104 degrees F, and the totally enclosed air-over motor is cooled by the airstream itself, which is what makes it appropriate for shop and warehouse service.
Discount Cleaning Products is an authorized dealer with US-based support, and we stock the replacement parts and consumables that keep commercial cleaning equipment in service rather than in a corner. If you are not certain this is the right part for your machine, send us the model and serial number and our team will confirm the fit before you order.
