On a portable extractor the male quick disconnect takes the abuse. It is the plug on the wand or hand tool, so it gets dragged across concrete, dropped on stairs, and connected and disconnected dozens of times a week. Once the sealing surface is scored, the coupler sprays a fine mist every time the trigger is pulled. This is the factory Sandia 10-0870-STA106 male straight-socket quick disconnect, the plug half of the pair that mates with the 10-0868-STA106 socket on the solution hose. Replacing it is a five-dollar-class fix for a problem that otherwise sends a working machine to the shop.
Built for
- Technicians who swap a wand for an upholstery tool several times per job.
- Restoration and janitorial crews whose tools live on hard floors and truck beds.
- Shops standardizing every Sandia tool in the fleet on the same 1/4-inch coupler.
- Anyone whose leak follows the tool rather than the hose when tools are swapped.
How to tell this is the part you need
Swap tools and watch where the leak goes. If the drip moves with the tool, the male plug is the problem; if it stays with the hose, replace the female socket, Sandia 10-0868-STA106. Look for bright scoring or a flat spot on the sealing land of the plug, or a plug that feels loose in a known-good socket. Either symptom means the plug is worn past the point where new O-rings help.
Specifications
- Sandia part number 10-0870-STA106.
- Type: male quick disconnect, straight socket.
- Size: 1/4-inch.
- Application: extractor wand, hand tool, or turbo tool to solution hose.
- Mating half: Sandia 10-0868-STA106 female straight-socket QD.
Sandia warranty
- 2-year warranty on all vacuum motors.
- 2-year warranty on 100 psi pumps only; 1-year warranty on all other pumps.
- 90 days on parts, tools, and accessories.
The warranty does not cover defects or failures resulting from improper or absent maintenance, misapplication, misuse, tampering, or substitution of provided parts. It also does not cover a pump stored in freezing conditions, a pump run for extended time with no water, use of powdered detergent, failure to flush the system regularly with a vinegar solution, filters removed from the solution tank, or pumps with inline filters that are not cleaned regularly. Sandia covers up to one year of service labor at the manufacturer calculated hourly labor rate when performed by a manufacturer-authorized service provider; after one year the original retail purchaser is responsible for all labor costs. Authorized warranty replacement parts must come directly from the manufacturer, and any other parts void the warranty. Contact the manufacturer before changing out parts, and do not return parts or equipment without an RMA number and approval. Warranty starts on the purchase date by the original purchaser from an authorized distributor, subject to proof of purchase.
Frequently asked questions
Is the male quick disconnect the half on the tool or the hose?
On a standard Sandia setup the male plug is on the wand or hand tool and the female socket is on the solution hose. Check your machine before ordering, since some shops reverse the convention.
Can I replace just the male half?
Yes, if only the plug is worn. If both halves are original and the pair has been in service for years, replacing both at once gives a better seal than mixing a new plug with a worn socket.
Will this work on a heated Sandia extractor?
Yes, it is used on the solution line of both heated and unheated Sandia extractors. Heated machines require the stainless steel hand tool rather than the clear plastic version.
Do I need thread sealant to install it?
The coupling half itself pushes into the socket and needs no sealant. Any threaded joint behind it into the tool valve should be sealed per the tool instructions.
Why not use a hardware-store quick disconnect?
Dimensionally many 1/4-inch couplers interchange, but Sandia requires warranty replacement parts to come from the manufacturer. Substituting parts on a machine still under warranty can void that coverage.
Buying from an authorized Sandia dealer
Discount Cleaning Products is an authorized Sandia dealer, so this is the factory part rather than a look-alike. That matters twice over on a machine still under warranty: Sandia requires warranty replacement parts to come directly from the manufacturer, and substituting other parts voids coverage. Our US-based team works with these extractors every day and can confirm the right part number for your serial and pressure rating before you order, so you are not guessing from a parts diagram.
