A cordless cart vacuum that will not spin up, or that runs but moves no air, has usually reached the end of its motor rather than the end of its useful life. This ProTeam 36 volt DC replacement motor assembly, part number 103732, is the repair part that keeps a legacy battery-powered ProTeam cart machine on the floor instead of in the scrap pile. It ships with crimps - pre-terminated leads - which is what turns a shop-level job into something a competent facility maintenance tech can finish with hand tools and a crimper.
Built for
- Motor failure repair on an aging ProTeam battery-powered cart vacuum - no suction, no spin-up, or a motor that grinds and dies under load
- Vacuum repair shops carrying OEM motors for legacy ProTeam cordless equipment
- Facility maintenance teams keeping a working machine in service rather than buying a replacement unit
- Stocking a spare motor for a fleet of older cart vacuums while OEM supply lasts
Fitment note - read this one carefully
The catalog description for this part carries the designation QV-300, which reads like a machine model but appears to be ProTeam internal code for the motor rather than a separate product line. The only distributor parts reference we could verify ties manufacturer part 103732 to the ProTeam GoCartVac, and that same reference flags the part as discontinued by the manufacturer. Separately, the ProTeam GoFree Flex Pro cordless machines are documented as using their own distinct 36 volt DC motor part numbers, so do not assume this motor crosses over to a GoFree. We are telling you the discrepancy rather than papering over it: confirm 103732 against your own machine parts diagram, or send us the model and serial and we will check it with you before you order.
Why crimps matter
A motor supplied with crimp-terminated leads takes the wiring guesswork out of the swap. There is no splicing a bare motor into an existing harness and hoping the terminations hold up to vibration; the leads land where the old ones came off. For a shop that is billable time saved, and for an in-house tech it is the difference between a repair that gets attempted and one that gets deferred until the machine is written off.
Specifications
- Manufacturer: ProTeam
- Manufacturer part number: 103732
- Type: replacement motor assembly
- Voltage: 36 volt DC
- Supplied with: crimp-terminated leads
- Documented fitment: ProTeam GoCartVac per distributor parts reference - verify against your machine
- Wattage and amp draw: not published by the manufacturer
Frequently asked questions
What machine does this motor fit?
The distributor parts reference we could verify lists it for the ProTeam GoCartVac. The catalog designation QV-300 appears to be an internal motor code rather than a separate machine model. Confirm against your own parts diagram before ordering, and do not assume it fits a GoFree Flex Pro, which uses different motor part numbers.
Is this part still made?
A distributor parts reference flags 103732 as discontinued by the manufacturer, so OEM supply for this motor is finite. If you run a fleet of these machines it is worth stocking a spare rather than waiting until one fails.
What does with crimps mean?
The motor arrives with pre-terminated crimp connectors on its leads, so the wiring lands on the existing harness without splicing bare wire. It makes the swap a field-serviceable job rather than a bench rebuild.
How do I know the motor is the problem and not the battery?
Check the battery pack and charger first, then the switch and wiring. A pack that will not hold charge produces the same no-run symptom as a dead motor and is far cheaper to address. A motor that spins but moves no air is usually a blocked airway or failed fan, not a dead motor.
What tools do I need to install it?
A general vacuum motor swap needs basic hand tools plus a wire crimper for the connections. Disconnect and isolate the battery pack before starting any work on a cordless machine.
Discount Cleaning Products is an authorized dealer for the brands we sell, so the parts on this page are genuine manufacturer components rather than look-alike substitutes. Our support is US based, and if you are unsure which part your machine takes, send us the model and serial number and we will work through the parts diagram with you before you order. We would rather spend five minutes getting the fitment right than have you return the wrong part.
