When a Sandia Sniper heated extractor stops making hot water, the failure is very often not the heating element itself but the plumbing around it. The 10-0801-B copper adapter is one of the reducing fittings inside that heater circuit, stepping a 3/4-inch connection down to 1/2-inch so the heat exchanger ties cleanly into the solution line. Carpet cleaning technicians and in-house facility maintenance staff buy this part when they are rebuilding a heater assembly, chasing a slow drip inside the motor base, or replacing a fitting that scale and thread sealant have finally worn out.
Copper is used here for a reason. The solution side of a heated extractor sees hot water, detergent residue and mineral load on every job, and a copper fitting handles that thermal cycling without the creep and cracking that eventually shows up in plastic. Replacing a single tired adapter is also a fraction of the cost and downtime of sending a machine out for service, which is why most shops keep a small bag of heater fittings on the truck.
Built for
- Rebuilding the in-line heater assembly on a Sandia Sniper heated carpet extractor
- Stopping a leak at a 3/4-inch to 1/2-inch transition inside the heater plumbing
- Restoring a machine after descaling, when old fittings come apart and do not reseal
- Stocking a preventive-maintenance parts kit alongside sensors, elbows and hose
A note on maintenance that will make this fitting last: Sandia's own manual asks owners to flush the solution system regularly and to run a diluted vinegar solution through the lines every two weeks to prevent mineral deposit build-up. Scale is what narrows a heater circuit, drives pressure up at the joints and eventually starts weeping at a fitting. If you are replacing this adapter because of a leak, descaling the rest of the circuit at the same time is worth the extra ten minutes.
Specifications
- Manufacturer: Sandia Products
- Part number: 10-0801-B
- Description: Copper heater adapter, 3/4-inch x 1/2-inch
- Material: Copper
- Assembly: Sniper heated extractor in-line heater circuit
- Sold as: Single fitting
Warranty
Sandia warranty policy as published by the manufacturer:
- 2-year warranty on all vacuum motors
- 2-year warranty on 100 psi pumps only; 1-year warranty on all other pumps
- 90 days on parts, tools, and accessories
This warranty does not cover defects or failures resulting from improper maintenance or lack of maintenance, misapplication, misuse, tampering, or substitution of provided parts. It also does not cover a pump stored in freezing conditions, a pump run for an extended time with no water, use of powdered detergent, or failure to clean the system regularly. Sandia also states that authorized warranty replacement parts must come directly from the manufacturer; using non-authorized parts can void the machine warranty.
Frequently asked questions
Will this fit my Sandia machine?
The 10-0801-B is a Sandia heater-circuit fitting for Sniper heated extractors. Sandia has revised heater assemblies over the years, so check the part number against the parts list for your model and serial number, or send us your model and serial and we will confirm it before you order.
Is this the heating element?
No. This is a copper reducing adapter that connects parts of the heater circuit. The heating elements and the heat exchanger tube are separate part numbers.
Do I need thread sealant when I install it?
Follow Sandia's service guidance for your machine. Threaded fittings in a pressurised solution line are normally sealed on reassembly, and old sealant should be cleaned off the mating threads first so the new joint seats properly.
Why did my old fitting fail?
The most common causes on a heated extractor are mineral scale build-up and thermal cycling. Sandia recommends flushing the system after each job and descaling with diluted vinegar every two weeks; skipping that shortens the life of every fitting in the circuit.
Does using this part affect my machine warranty?
Sandia states that authorized warranty replacement parts must come directly from the manufacturer and that other parts can void the warranty. This is a genuine Sandia part supplied by an authorized dealer.
Buying from Discount Cleaning Products
Discount Cleaning Products is an authorized Sandia dealer. We stock genuine Sandia service parts rather than generic look-alikes, so the part you install is the part the machine was built around and your equipment warranty stays intact. Our US-based support team works with Sandia extractors, flood pumpers, air movers and backpack vacuums every day, so if you are unsure which revision of a part your serial number takes, contact us before you order and we will check it against the Sandia parts list with you.
