Weak vacuum is the single most common complaint on a portable carpet extractor, and Sandia's own troubleshooting guide lists a damaged or loose vacuum hose near the top of the causes. The 10-0806 is the 1-1/2-inch grey hose barb fitting that makes the internal vacuum connection on Sniper extractors. In Sandia's parts lists for the Sniper 12-gallon 500 psi machine it appears as item 12 in both the heated and non-heated builds, one per machine, mating to the 1-1/2-inch black-lined grey hose that runs inside the base.
A barb fitting fails quietly. It does not break in half; it gets nicked when the hose is pulled off, or the barbs wear smooth, and the joint stops holding a proper seal. The result is an air leak that never shows up as a puddle but costs you lift at the wand, leaves carpet wetter, and makes the machine feel tired. If you have already emptied the tank, cleaned the float screen, reseated the lid gasket and checked the dump valve and the vacuum is still down, the internal connections are the next place to look.
Built for
- Restoring a leaking or worn 1-1/2-inch internal vacuum hose connection on a Sniper extractor
- Chasing a loss-of-lift complaint after the tank, float screen and lid gasket check out clean
- Rebuilding the vacuum plumbing on a used or high-hour machine
- Replacing a barb damaged during hose removal or tank service
While the base is open, it is worth working through the rest of Sandia's vacuum checklist: clean the vacuum float assembly screen, which the manual says should be done daily and which is the most common single cause of lost airflow; confirm the hose clamps are tight; and check the 1-1/2-inch hose itself for cuts and soft spots. Sandia also warns that operating the machine without a properly maintained float assembly will greatly decrease vacuum motor life and can void the warranty, so a fitting replacement is a good moment to inspect the whole recovery path.
Specifications
- Manufacturer: Sandia Products
- Part number: 10-0806
- Description: 1-1/2-inch grey hose barb fitting
- Parts list reference: Item 12, Sniper 12-gallon 500 psi parts lists (heated and non-heated)
- Quantity used per machine: 1
- Mates with: 1-1/2-inch black-lined grey vacuum hose
Warranty
Sandia warranty policy as published by the manufacturer:
- 2-year warranty on all vacuum motors
- 2-year warranty on 100 psi pumps only; 1-year warranty on all other pumps
- 90 days on parts, tools, and accessories
This warranty does not cover defects or failures resulting from improper maintenance or lack of maintenance, misapplication, misuse, tampering, or substitution of provided parts. It also does not cover a pump stored in freezing conditions, a pump run for an extended time with no water, use of powdered detergent, or failure to clean the system regularly. Sandia also states that authorized warranty replacement parts must come directly from the manufacturer; using non-authorized parts can void the machine warranty.
Frequently asked questions
Which machines use the 10-0806?
Sandia lists it as item 12 in both the heated and non-heated parts lists for the Sniper 12-gallon 500 psi carpet extractor, one per machine. Other Sniper extractors in the range use the same 1-1/2-inch vacuum plumbing. Confirm against the parts list for your model and serial number, or ask us and we will check.
What is the difference between the 10-0806 and the 10-0806-2?
Size. The 10-0806 is the 1-1/2-inch barb fitting and the 10-0806-2 is the 2-inch version. Match the fitting to the hose diameter on your machine.
Will a new barb fitting fix my weak vacuum?
It will fix vacuum loss caused by a bad connection at that joint. Sandia's troubleshooting guide also lists a full recovery tank, a dirty float screen, a stuck float ball, an open dump valve, an unsealed access lid, a clogged hose and a clogged air intake grid. Work through those first, since most are free to fix.
Do I need new hose clamps?
Inspect them. Sandia uses 3/4-inch hose clamps elsewhere in the machine and a clamp that has been over-tightened or corroded will not pull the hose down evenly onto a new barb.
Is this a genuine Sandia part?
Yes. Discount Cleaning Products is an authorized Sandia dealer supplying genuine Sandia service parts.
Buying from Discount Cleaning Products
Discount Cleaning Products is an authorized Sandia dealer. We stock genuine Sandia service parts rather than generic look-alikes, so the part you install is the part the machine was built around and your equipment warranty stays intact. Our US-based support team works with Sandia extractors, flood pumpers, air movers and backpack vacuums every day, so if you are unsure which revision of a part your serial number takes, contact us before you order and we will check it against the Sandia parts list with you.
