Every window cleaner who has moved to pure water has had the same argument with a spreadsheet. Deionization resin is easy to buy and brutal to keep buying, and in a hard-water service area a dual DI setup can be exhausted in a single day. The Tucker H2Pro exists to change that math. It puts a reverse osmosis membrane between your tap and your resin, so the DI stage is polishing water that is already most of the way there instead of doing all the work alone.
Then it does something most systems do not: it lets you switch the resin out of the circuit entirely. DI Saver Mode bypasses the deionization stage and delivers RO-only water, which is exactly what you want for solar panels and other non-transparent surfaces where a zero TDS rinse buys you nothing. Resin gets consumed on the jobs that need it and nowhere else.
Built for
- Multi-crew contractors running more than one pole. Tucker builds and markets the H2Pro for feeding multiple water-fed poles from a single cart, which is where a compact system starts to bottleneck a crew.
- Volume solar panel cleaning. The DI Saver bypass is aimed squarely here, and on a large array the resin savings across a season are not a rounding error.
- High-TDS service areas. Above roughly 100 parts per million in the feed, a deionization-only setup stops being economical, and an RO and DI system is the fix rather than a luxury.
Why the build details matter
Stainless steel housings and flat-free wheels are not a spec-sheet flourish. Cracked plastic housings and flat pneumatic tires on gravel and curbs are the two things that take a pure water cart out of service, and both are designed out here. The cart runs vertically or horizontally, which sounds trivial until you are trying to fit it in a van alongside poles, hose reels and a ladder.
Assembly is done in the USA at Reach Higher Ground in Castle Rock, Colorado, which matters less for national pride than for parts and support turnaround when a membrane or a housing needs replacing mid-season.
Specifications
- Configuration: three-stage carbon, reverse osmosis and deionization pure water cart
- Booster pump: 2-plus GPM, 110 volt, with built-in on and off switch
- Carbon pre-filter: 30 inches
- Reverse osmosis membrane: 40-inch Tucker MAX-Flow
- Deionization post-filter: 30 inches, final polish
- DI Saver Mode: bypasses the DI stage for reverse-osmosis-only output
- Housings: stainless steel
- Frame: wheeled cart with flat-free wheels; runs vertically or horizontally
- Assembly: assembled in the USA, Castle Rock, Colorado
- Part number: 10041-110v-SS, the 110-volt configuration
What we are not going to tell you
Tucker does not publish dimensions, shipping weight, hose fitting sizes, deionization resin capacity or a maximum feed TDS for the H2Pro, and the pure water output figure quoted around the industry traces back to the booster pump rating rather than a measured permeate rate. We would rather leave those blank than fill them in with a plausible guess. Warranty coverage on this SKU is also worth confirming at order time, since Tucker's current sitewide terms and older distributor listings do not agree. Ask us and we will get you the current answer in writing.
Frequently asked questions
What is DI Saver Mode?
A built-in bypass that skips the deionization stage so you work with reverse-osmosis-only water. On solar panels and other non-glass work that does not require a zero TDS rinse, that means resin is not being consumed, which is the largest running cost of a pure water system.
Does it need a tank?
No. The H2Pro produces water on site, running from a pressurized feed with the 110-volt booster pump raising pressure across the reverse osmosis membrane. It is a production cart rather than a tank system.
Can it run two poles at once?
Tucker markets the H2Pro for running multiple poles. Tucker does not publish a simultaneous two-pole flow figure, so we will not quote one. Tell us your crew size and feed water TDS and we will give you an honest read on whether it fits your workflow.
Does it include a TDS meter?
No inline TDS meter is listed in the H2Pro specification, so plan on a handheld meter. Checking TDS is how you know whether the membrane or the resin is the thing that needs attention.
Do I need reverse osmosis, or is deionization alone enough?
It depends on your feed water, not on preference. The working benchmark in the trade is around 100 parts per million: below that, a deionization-only setup can pencil out, and above it resin burn makes an RO and DI system cheaper over a season. Measure your tap water before deciding.
Why does output drop in winter?
Cold feed water reduces reverse osmosis permeate flow more than it reduces drain flow, so both production and waste ratio get worse in cold months. That is expected behavior for every RO system, not a fault.
Discount Cleaning Products is an authorized Tucker dealer with US-based support before and after the sale. Tell us your crew size, your feed water TDS and the mix of glass and solar work you do, and we will tell you honestly whether the H2Pro is the right system or more than you need.
