Genuine Sandia 10-0834 motor mount plate washer that seats the vacuum motor in 50-40 series spot extractors.

Genuine Sandia black anodized lid rivet for 10-quart Raven backpack vacuum lids.

Genuine Sandia lid latch replacement for Raven backpack vacuums.

Genuine Sandia valve clamp that re-secures the valve on a stainless steel hand tool.

Genuine Sandia 10-0836-L replacement wheel axle that restores straight rolling on Bridgepoint Sniper extractors.

Genuine Sandia replacement vacuum hose for the SX-12 12-inch hard surface turbo brush tool.

Sandia 60-0012 Force 14 Female Receptical

Sandia 60-0015 Force 14 Belt for Clutch/Gear

Sandia 60-0032-B Bracket for Cord Protector Strap (Use with 60-0032-A)

Sandia 60-0033 Force 14 LED Cover

Sandia 80-0042 3/8FJIC Crimp Fitting

Genuine Sandia 10-0843-A 3/8-inch black internal hose assembly for Sniper carpet extractors.

Sandia 80-0115 3/8" MPT x 1/2"Barb Brass 90

Sandia 80-0115-B 3/8" MPT x 1/2" Barb Brass- do not order- comes with 1200 psi pump

Sandia 60-0041 FRONT CASTER ADJUSTMENT BUTTON FORCE 14

Genuine Sandia wire finger guard that shields the steel fan blade on a Sandia air mover.

Waist belt extension that adds up to 12 inches of strap to a Sandia Raven backpack vacuum harness.

Genuine Sandia 90-degree female pipe thread elbow for the heater circuit on Sniper heated carpet extractors.

23 inch Sandia plastic pick-up tool for vacuuming debris out of hard to reach spaces.

The genuine Sandia 1/8-inch male quick disconnect fitting for spotter solution lines.

Genuine Sandia service part that restores the powerhead electrical connection on a backpack vacuum.

Genuine Sandia air intake screen that guards the fan and fingers on a Sandia air mover.

Factory Sandia 1/4-inch male straight-socket quick disconnect plug for extractor wands and hand tools.

Sandia 60-0034 Force 14 Rear Castor

Sandia 80-0004-A 1/4" x 2" Brass Nipple

Sandia 80-0005-B 5 Amp. Circuit Breaker

Sandia 80-0006 45 Deg. Street Elbow

Sandia 80-0013 500 psi Switch Plate

Sandia 80-0032 3/8 Bulk Head Fitting

Sandia 80-0062 Rebuild kit for 200psi BPR

Factory Sandia 1/4-inch male NPT to 3/8-inch JIC 90-degree adapter elbow for extractor solution plumbing.

Genuine Sandia DB powerhead connector that cures an intermittent or dead brush circuit.

OEM motor mount plate for the Sandia 50-4000 spot extractor.

Sandia 80-0025 11003 Jet for 2-Jet Extractor Wand #3

OEM replacement swivel cuff for Sandia backpack and Raven vacuum hoses.

Genuine Sandia 10-0019-6 6-quart dual-cell noise filter quiets backpack vacuums and shields the motor.

Genuine Sandia cooling duct that channels cooling air over the Sniper extractor vacuum motor.

Sandia 80-0132 3/4"x2" Brass Nipple

Sandia 60-0005 Force 14 Green Switch

Sandia 90-1023 SHUT OFF VALVE FOR 4 GAL. SOLUTION TANK

Sandia 60-0010 Force 14 Cord to Head

Sandia 60-0011 Force 14 Brush Strip

Sandia 80-0005 15 Amp Circuit Breaker 1658-G21-06-P10-15 amp

Sandia 80-0017 Bulk Head fitting for Sniper

Sandia 80-0041 _FJIC Crimp Fitting

Factory Sandia foam insulation that wraps the extractor heater tube to hold solution temperature.

Sandia 80-0102-M 3/4" NPT Lock Nut

Splash-proof heater switch replacement for Sandia Sniper 6 and 12 gallon carpet extractors.

Sandia 60-0018 Force 14 Uphostery Tool w/Brsh

Sandia 60-0018 Force 14 Uphostery Tool w/Brsh

Copper 3/4-inch to 1/2-inch reducing adapter for the in-line heater circuit on Sandia Sniper heated carpet extractors.

Genuine Sandia female quick disconnect for the 15-inch turbo tool solution line.

Factory Sandia 1/4-inch female straight-socket quick disconnect for extractor solution hoses and wands.

Sandia 60-0043 PAPER BAG SENSOR

Sandia 80-0003-12 1-1/2" Black Lined Gray Hose

Sandia 10-0025 replacement on/off switch for Raven backpack vacuums and the Hipster hip vac.

The genuine Sandia replacement adjustable brush for the 11-inch 10-0347 carpet tool.

Genuine Sandia 3/4-inch copper adapter for the heater circuit on a Sniper carpet extractor.

Genuine Sandia copper tube for the in-line heater assembly on Sniper heated carpet extractors.

Sandia 60-0040 FRONT CASTER WHEEL ON SHAFTWITH BEARING

Sandia 80-0004 1/4" x 4" Brass Nipple

Sandia 80-0005-A 7 Amp Circuit Breaker 1658G2106P10 7 AMP

Sandia 80-0009 1/4" Branch Tee

Genuine Sandia 1/4-inch brass tee fitting for Sniper 12-gallon 300 and 500 PSI carpet extractors.

Sandia 60-0002 Force 14 Crevice Tool

Sandia 1.5-inch 90-degree ABS street elbow for carpet extractor and spotter plumbing.

Sandia 6-quart reusable cloth filter bag for Raven 6 and Hipster backpack vacuums.

Sandia 90-1030 Air Mover Ring and Screen

OEM replacement brushes for the Sandia 10-0175 16-inch adjustable-brush carpet tool.

19-inch OEM replacement axle for Sandia Sniper carpet extractors.

Sandia 80-0014 3/8" B x 1/4" F 90 Deg.

Genuine Sandia 4-foot by 1-1/2 inch replacement backpack vacuum hose for Raven machines.

OEM replacement blade set for the Sandia 20-inch squeegee tool - restores a clean seal on wide wet pickup.

Factory Sandia 3/8-inch JIC male to 3/8-inch female JIC 45-degree swivel fitting for extractor plumbing.

Sandia 60-0028 Force 14 Powerhead Pigtail Cor

Genuine Sandia cloth filter bag material that restores airflow in a backpack vacuum.

Genuine Sandia replacement component for turbo brush tools in the Sandia vacuum accessory range.

Genuine Sandia 1-1/2-inch grey hose barb fitting for the internal vacuum hose connection on Sniper carpet extractors.

Genuine Sandia OEM 1-1/2-inch ABS fitting for carpet extractor tank and hose plumbing repairs.

4 inch Sandia utility tool for vacuuming seats, consoles and vehicle floor areas.

OEM C-channel that secures the push handle on Sandia 3-gallon spot extractors.

Genuine Sandia Bona-configuration pigtail cord that fixes the most common backpack vacuum electrical fault.

Genuine Sandia roller blade wheel for smooth-rolling spot extractor transport.

Complete Sandia 1/2-inch clear priming hose assembly that lets you watch a Sniper pump take prime.

Sandia 80-8004 Hose between Sniper Heaters

OEM extension that carries the run from the powerhead wand back to the vacuum on Sandia Raven backpacks.

Sandia 10-0197 6-quart micro-lined paper vacuum bags, 10-pack, for Raven 6 and Hipster vacuums.

Sandia 80-8006-A 24" Hose for Sniper w/ Heater

Genuine Sandia vacuum sleeve for the newer 6.6-inch two-stage vacuum motors used in Sniper extractors.

Sandia 80-0018 Ball Valve for Sniper for 200 PSI Pump

OEM pigtail cord for the Sandia 10-0164 powerhead motor - the small electrical part that ends most powerhead outages.

Genuine Sandia 10-0812-E Aquatec valve kit that restores 100 PSI check-valve sealing on Sniper extractor pumps.

Genuine Sandia swell latch that clamps the 15-inch spinner tool housing closed and sealed.

OEM 3-speed rotary switch restoring motor control on Sandia A.M. extractors.

Genuine Sandia waist belt extension for the Hipster 6-quart hip vacuum harness.

Four-pack of black OEM replacement blades for the Sandia 10-0170 14-inch squeegee floor tool.

Sandia 80-0002-A Hose for Sniper Manifold

Genuine Sandia 3-piece replacement head kit for carpet and upholstery wands.

Sandia 80-0007-D replacement spray tip for the No. 3 jet on 12-gallon Sniper extractor wands, 200 PSI and above.

Sandia 80-0005-C 10 AMP CB 1658-G21-06-P10-10AMP ETA

Mercury BF5-20

Genuine Sandia 3/8-inch black internal hose that keeps a Sniper extractor's solution line sealed.

Genuine Sandia 18-inch internal hose for 150 psi Sniper extractors running an inline heater.

15 inch Sandia Sidewinder crevice tool for seat gaps, baseboards and perimeter edges.

Genuine Sandia replacement jet for the 15-inch turbo spinner tool; two are needed for a full set.

Genuine Sandia male quick disconnect nipple for the 15-inch turbo tool solution line.

Sandia 50-1007 7 Ft. Black Hose for Spotter

Genuine Sandia 10-0822 intake and exhaust grate that keeps debris out of the Sniper extractor motor compartment.

Sandia 10-0019 10-quart dual-cell noise filter for quieter vacuum and extractor exhaust.

Sandia hose cuff that restores a tight, leak-free 1-1/2 inch to 2 inch vacuum hose connection.

Mercury BF5-31

Complete replacement lid assembly for Sandia Raven 6-quart backpack vacuums, supplied without hose.

Genuine Sandia replacement handle for the 10-0455 two-piece stainless steel spotter wand.

Genuine Sandia 3-inch round dust brush attachment for detail dusting and vents.

Genuine Sandia 1/8-inch female QD fitting for Spotter hand-tool hose connections.

A lighted, splashproof heater switch for Sandia Sniper heated carpet extractors.

Sandia 10-0507 8-inch black connector hose for the stainless steel hand tool.

Genuine Sandia brush drive belt for the Force 14 commercial upright vacuum.

Sandia 60-0029 Force 14 Powerhead Recepticle

Sandia 80-0111-A Filter for Clear View Filter

Genuine Sandia 5-inch upholstery tool that fits 1-1/2 inch Raven backpack vacuum wands.

OEM replacement felt blades for the Sandia 10-0173 14-inch felt floor tool - protects finished floors while it cleans.

Genuine Sandia 10-0812-A Aquatec 120 PSI pressure switch that cures pump chatter and no-shutoff on Sniper extractors.

A 1/4-inch female quick disconnect for tool-free hose and tool hookups on Sandia Sniper extractors.

Genuine Sandia 17-inch crevice tool for 1-1/2 inch Raven backpack vacuum wands.

Genuine Sandia 2-inch grey hose barb fitting for high-volume vacuum and recovery hose connections.

OEM Sandia adapter that joins the telescopic wand to the vacuum hose handle in the Turbo Brush Kit.

Genuine Sandia replacement jet tip for the 10-0861 dual-jet extractor wand.

Sandia 14 inch replacement nylon brush strip for the 10-0183 floor tool.

Genuine Sandia replacement felt blades that restore the seal and suction on a 14-inch scalloped hard-floor tool.

An 11-inch crevice tool for baseboards, corners, stair treads and gaps a floor tool cannot reach.

A genuine Sandia dome filter with bag support that protects the motor on Raven backpack vacuums.

Genuine Sandia complete solution hose assembly for spot extractors, supplied ready to connect.

Genuine Sandia three-way plug connector, an electrical service part for Raven backpack vacuums.

A genuine Sandia band that dampens vacuum-motor vibration and noise on Raven backpack vacuums.

Sandia 80-0143 3/4" Brass Street Elbow

Genuine Sandia 10-0026 17-inch 16/3 power cord pigtail for Raven backpack vacuums.

Genuine Sandia 10-0812-C Aquatec valve housing kit that restores check-valve sealing and spray pressure on Sniper pumps.

Genuine Sandia replacement vacuum recovery hose for the 15-inch turbo rotary hard surface tool.

Cream carbon motor brush for the Sandia XP-3 vacuum motor, Sandia part number 10-1333-C.

Green carbon motor brush for the Sandia 2-stage Sniper vacuum motor, part number 10-1333-G.

Sandia 60-0044 FRONT DOOR KIT FORCE 14

Sandia 10-0007-10 washable 10 quart cloth filter bag with L-style grommet for Raven backpack vacuums.

Genuine Sandia replacement solution hose for stainless steel spotter wands, restoring full jet pressure.

Sandia 80-0059-2 200psi Sniper Gauge

Genuine Sandia FORCE 14 top-fill replacement paper bags, 10 per pack (#60-1001).

Sandia 10-0181 28-inch crevice tool for deep-reach vacuuming with Sandia backpack and hip vacuums.

Black carbon motor brush for Sandia Super vacuum motors, Sandia part number 10-1333.

OEM 7-foot replacement vacuum hose for Sandia 3-gallon spot extractors.

The genuine Sandia replacement brush for the 14-inch horse hair floor tool.